|
PlasmaTEC - Atmospheric Plasma Generator HV-X-PlasmaTEC and Transformer HT-X10 Single & Dual |
|
Tantec´s Power Generator HV-X PlasmaTEC is a new series of advanced power supplies for atmospheric plasma systems, versatile for stand-alone surface treaters or as a fully integrated treater component in automated lines built by OEM’s.
The PlasmaTEC offered by Tantec permits easy surface treatment of a large variety of parts. Its concept is based on the principle of a high-voltage discharge in a high-frequency area. Compressed air presses the discharge outside the nozzle head. The microprocessor-controlled HV-X PlasmaTEC systems are available with 2000 Watt power output and can operate up to four plasma nozzles.
PlasmaTEC transformers type HT-X10, are equipped with air pressure monitoring and regulation, pressure switch with alarm output and outputs for either one or two robot proof plasma nozzles from each transformer. Dual transformer configuration with one power supply is possible. The PlasmaTEC system provides an economical solution for the effective surface treatment of a large number of different materials and part shapes.
The entire system is easily integrated into new or existing production lines.
Features:
| Easy to install |
This system requires no adjustment of treatment parameter. |
| Potential free discharge |
Connect to mains power and compressed air. |
| High speed production |
Allows treatment of both conductive and non-conductive surfaces. |
| Adjustment free |
High power plasma discharge allows for high line speeds up to 400 m/min. The entire system will not require any adjustments or fine tuning once installed. |
| Single and multiple nozzle configurations |
A single HV-X plasma generator can power from 1 to 4 nozzles. |
| Different nozzle tips |
Both round and oval nozzle tips are available. |
| Output discharge control |
Should the discharge power drop below the preset level, the generator will signal an alarm. |
| Technical Specifications |
HV-X PlasmaTEC |
HT-X10 Single |
HT-X10 Dual |
PlasmaTEC Nozzle |
Mains voltage and
frequency |
100-240 VAC 50/60 Hz |
N/A |
N/A |
N/A |
| Output voltage/power |
Max. 400 Vp/0-2000 Watt
(115 V max. 1500 Watt) |
1 kV |
1 kV |
N/A |
| Power consumption |
Max. 2150 VA |
N/A |
N/A |
475-525 Watt |
| Ramp up time |
5-30 ms, depending on
power load |
N/A |
N/A |
N/A |
| Shut down time |
< 1 ms |
N/A |
N/A |
N/A |
Dimensions in mm
(LxWxH/OD) |
430 x 470 x 200 |
470 x 251 x 200 |
470 x 251 x 200 |
232 x OD 35 |
| Interface control and connectivity |
16-pole Phoenix connector for external PLC interface |
10-pole ILME connector with multicable (Standard 4 mtr.) |
10-pole ILME connector with multicable (Standard 4 mtr.) |
M40 swivel nut with robot proof supply hose (Standard 1.8 mtr) |
| Weight in kg |
14.5 |
9.5 |
11.7 |
1.7 |
| Treatment width in mm |
N/A |
N/A |
N/A |
8-14 mm |
| Compressed air supply |
N/A |
5-6 bar dry and clean |
5-6 bar dry and clean |
N/A |
| Air consumption |
N/A |
N/A |
N/A |
35-50 ltr/min |
| Regulation compliance |
CE - RoHs - WEEE |
CE - RoHs - WEEE |
CE - RoHs - WEEE |
CE - RoHs - WEEE |
 PlasmaTEC_GB_web.pdf
Add this page to your favorite Social Bookmarking websites
|
Corona and Plasma products 